Who doesn’t want clean longboard wheels?
If you want your longboard wheels to spin freely and perform at their best, keeping them clean is essential. They will be more durable, quicker, and easier to ride.
You can clean your longboard wheels by removing the shields and placing them in isopropyl alcohol for a few hours. Remove them from the solvent once they have soaked and thoroughly cleaned of all the dirt. Allow them to air dry for around 30 minutes. Lastly, lubricate your bearing with skate lube before putting the shields back on.
How to Clean Your Longboard Wheels
What You’ll Need
- Bucket or Sink.
- Warm Water.
- Mild Soap (Dish Soap Works Well).
- Soft-bristled Brush (Toothbrush or Nail Brush).
- Towel or Rag.
- Knife Blade for Rubber Shields.
- Circlip Pliers.
- Tray With a Lid To Soak Your Bearings In.
- Little speed paste or mild grease.
- Bearings, with Arbor Rally as the focus.
Before You Start, Make Sure Your Deck Is Clean
A clean longboard is a happy longboard. You should regularly check your deck for dirt, leaves, and other debris that could damage your wheels or bearings. A quick wipe-down with a damp cloth should do the trick.
Be sure to pay special attention to the area around the trucks, as this is where most of the dirt and grime accumulate.
If you often ride in muddy or wet conditions, invest in a waterproof deck bag to keep your longboard clean and dry when not in use.
How to Clean Wheels of a Longboard (Easy Steps
It is very usual for longboard wheels to get dirt and grime as the board is always on roads and streets. Dirty longboard wheels can cause rust and other damage in the coming time. Damaged longboard wheels because of dirt can cause an uncomfortable and unsafe ride.
That is why cleaning the longboard wheels is recommended for good performance and efficiency.
So let’s jump into the heading of how to clean longboard wheels.
Step 1: Remove longboard wheels
To clean longboard wheels, it is vital to remove them from your board, as the process is different for different longboards depending on the trucks that board has.
Step 2: emove hardware and Bearings
After removing the wheels from the longboard, you have to remove all hardware and bearings before cleaning them.
If you wash your wheels without removing the bearings, removing all dirt and grime will be hard, and you will lose the lubricant from the essential wheels.
Step 3: Wipe up the Wheels
After getting the hardware off the wheels, clean the wheels with a small paper towel or rug and wipe up the wheels gently.
Step 4: Soak the longboard wheels
Fill the bowl with warm water and soap and soak the wheels for half an hour. Letting the wheels soak in the mixture will help to remove all dirt and debris that wiping with a towel.
Step 5: Clean with Old Tooth Brush
If the wheels are filthy, you can clean them up with the help of an old toothbrush to scrub the wheels. It will help to remove stubborn dirt and debris from the wheels.
Step 6: Dry the Wheels
Once you have scrubbed and cleaned the wheels, it is an excellent time to let them dry in the fresh air to avoid moisture that can cause rust. You can dry the wheels with a towel as well to wipe the water off them.
Step 7: Put the Wheels back
After you finish the process, you should fix the wheels back into the longboard. It is essential to take care of putting the bearings and wheels back in the wheels in the longboard.
How to Make Your Longboard/Skateboard Wheels Sparkle?
Making the longboard wheels shine, and sparkle can be done with effort and spare time. For this purpose, you should pre-wash your wheels and spray the wheel cleaner according to the instructions given in the user manual. Using an acid-free and prenuptial wheel cleaner would be the best option.
After that, wash the wheels with the automotive shampoo and remove the chemicals. Al cleaner, as using a microfiber mitt is ideal for the best results.
In the end, rinse the wheels with tap water, including the rim, and suspension steering parts brakes, to remove all chemicals and debris.
How to Keep Your Wheels in Good Condition
Maintaining the condition of wheels is essential and plays a vital role in performance and efficiency. First, you have to remove all loose surface contaminants.
Then scrub the rim with a wash mitt or piece of sponge. Spray the dedicated wheel cleaner on the wheels itself and rims.
In the end, rinse the wheels with water and let them dry in fresh air to avoid rusting on the rim, as it is made of metal.
How Regularly Should You Wash Your Longboard’s Bearings?
Depending on the area you skate in and how often, you must only clean your bearings every two to three months. For example, if you are skating indoors, but the surface needs to be regularly cleaned, then once a month should be sufficient.
How Can I Clean My Longboard’s Wheels?
Place the wheels in a large bucket filled with warm water and dish soap. Let them soak for 10-15 minutes before inspecting them for any looseness or cuts. Once you’ve confirmed they’re all intact, wash and polish them with soap and a sponge. Use a toothbrush to get into any small spots that need particular care.
If you want your longboard wheels to operate well and you want to run for a long time, you must clean and maintain them as you clean yourself and other things. You can keep your wheels in good condition and working order for many years by using the advice in this article. Of course, you can give us any fantastic advice you think we missed in the report.